Craft Room Project: First Router Attempt

First Attempt: Joining Tongue & Groove - Close Fit

While this so isn’t perfect, it absolutely blew apart my expectations for my first ever attempt at using not just a router, but bits that are apparently on the finicky side to use. I’m actually really happy with this little mess! (Sorry for the less than stellar photos, I just nabbed them quickly with my phone and didn’t realize how bad they were until I got them loaded!)

The first thing I attempted was cutting the tongue portion of what would become a tongue and groove join. This after more than an hour reading the directions and figuring out the basics of attaching the bit and adjusting depth and all the other VERY different nuances of using a router than any other power tool I’ve used so far.

First Attempt: Tongue Cut
First Attempt: Tongue Cut

As you can see, this is really wrong as that tongue isn’t supposed to be wedge shaped. I was working on figuring out how to keep the router flat on such a narrow piece of wood and obviously failed on that pass. I was still thrilled that it came even close to what I knew it was supposed to look like.

The second one of these came out much better, but was still not perfect.

Second Attempt: Tongue Cut
Second Attempt: Tongue Cut

It isn’t supposed to have that angled divot in it.

Second Attempt: Tongue Cut - Placement Goof
Second Attempt: Tongue Cut – Placement Goof

I’m totally okay with not perfect at this point. The tool is doing what it is supposed to do and the tongue piece itself came out wonderfully. The problems with this cut can be solved with a little practice and I’m good with playing some more.

The other part of this join, the groove, was surprisingly easy and came out mostly clean.

First Attempt: Groove for Tongue Joint
First Attempt: Groove for Tongue Joint

Part of why I’m surprised this came out as cleanly as it did was the fact that the router tended to hit in places and jerk a little. I think those were places where there were knots in the wood. This was probably close to a 3 foot long cut and it only had one noticeable wobble in the groove.

Wobble Oops on Tongue Groove
Wobble Oops on Tongue Groove

Considering this was the first time attempting this, I’m thrilled as this was the piece I was most concerned about being able to pull off.

The true test of how well this little play session was is seeing if those pieces actually fit together. And yes. Yes they did!

First Attempt: Joining Tongue & Groove
First Attempt: Joining Tongue & Groove

It was such a nice, snug fit, I wasn’t certain when I first tried it that it was going to work. Then it just snugged in perfectly.

First Attempt: Joining Tongue & Groove - Close Fit
First Attempt: Joining Tongue & Groove – Close Fit

The above picture makes me excessively happy in that it not only fit together, but it LINED UP! The surfaces of both pieces hit at the same spot. Sure, the edge of the one is a little rough, but a little sandpaper or a file will fix that completely.

Being able to pull these cuts off is a critical piece to building the cabinet doors. If I couldn’t pull this off, then I was going to have to look into a much more expensive option of getting a table saw and special blades. I’m almost certain after this experiment that I’ll be good with that I currently have.

The cool thing about this is even if it isn’t perfect, I’m still probably going to be good. I’m going to paint the cabinets, so any small things can either be fixed with wood filler or I might even leave some of the imperfections and keep these looking a little more rustic. The wood I use on the cabinets is also going to be a much better quality than what I used here. It will probably cut more cleanly than these did because of that.

I still need to practice more and try and work out some of the kinks to make sure the cuts are cleaner than what I got today, but this was a promising start.

Next up to test out and play with will be the nail guns. I think that all the playing I need to do to get ready for the cabinets is going to be its own project. I have enough wood, I think I’m going to build a small storage box for outside. If it is ugly, that’s perfectly fine, but it will give me the practice with all the new tools that I need.

I’m so happy with how everything worked out today!

Now I just REALLY need to hear back from this last company on a bid. I sent an email yesterday, so hopefully that will get a response soon.

Author: TJ Fox

I am a slightly sane artist, amateur photographer, book addict, wife, mom and raging introvert. I have more hobbies than I can count, so it is beyond shocking that I manage to find time to do any of them, let alone most of them and still have time to do anything else. Of all the talents I claim, writing wasn’t one of them until my muse dropped the idea for a book on my head.

9 thoughts on “Craft Room Project: First Router Attempt”

      1. I’m really not like this all that often, though I’d say I am more so lately. I’m definitely more comfortable taking risks when it comes to things that fall into a creative vein than just about anything else, though.

        Liked by 1 person

    1. Thanks! I do wear safety glasses and a mask whenever I do any projects that my cause things to fly. I’m more scared of accidentally doing something stupid and cutting myself. My family used to joke that when my dad worked on a project (which was often), it wasn’t a success unless blood was drawn (never anything really bad, just something that caused him to bleed). I just really hope that I don’t follow that trend.

      Liked by 1 person

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.